How to Fix a Leaky Faucet
A dripping faucet is more than annoying — a faucet that drips once per second wastes more than 3,000 gallons of water per year. Most faucet leaks come down to a worn O-ring, a failed cartridge, or a deteriorated washer. With the right parts and a methodical approach, most homeowners can fix a leaky faucet in an afternoon.
Faucet leaks fall into a few predictable categories: water dripping from the spout when the faucet is off, water seeping around the handle, water pooling at the faucet base, or moisture appearing under the sink at the supply connections. Each location points to a different component, and identifying the source before disassembly saves time and prevents unnecessary parts replacement.
The repair procedure depends on the faucet type. Compression faucets, cartridge faucets, ball faucets, and ceramic-disc faucets all use different internal mechanisms. A cartridge replacement that fixes a Moen single-handle faucet will not help a Delta ball faucet. Knowing what you have before you start is the difference between a one-trip repair and multiple hardware store runs.
This guide covers the full process: locating the leak, identifying the faucet type, shutting off the water safely, disassembling the faucet, replacing the worn components, reassembling correctly, and testing the repair. It also covers when the job has moved beyond a homeowner repair and a licensed plumber is the right call.
Identify Where the Leak Is Coming From
Before touching a wrench, spend two minutes watching the faucet. Where exactly is the water appearing? The location tells you which component has failed and which repair to make.
Dry the area around the faucet completely with a towel, then run the faucet briefly and watch carefully. Look at the spout, the base of each handle, the faucet body where it meets the sink deck, and the supply connections under the sink. Each location points to a different failure.
Drip from the spout
Water drips from the spout when the faucet is fully off. This is almost always an internal component failure — a worn cartridge, a deteriorated O-ring or washer, or a damaged valve seat. The repair is internal.
Leak around the handle
Water seeps out around the base of the handle when the faucet is running or when the handle is turned. Usually caused by a worn O-ring on the cartridge stem or a failed packing seal. The repair involves removing the handle and replacing the seal.
Leak at the faucet base
Water pools around the base of the faucet on the sink deck. Often caused by worn O-rings on the faucet body itself, or a failed deck gasket. Requires removing the faucet or accessing the base seals.
Leak at supply connections
Moisture or dripping at the supply line connections under the sink. May be a loose connection, a deteriorated supply line, or a failed shutoff valve packing. Often fixable by tightening the connection — but inspect the line and valve carefully before assuming a simple fix.
Leak under the sink with no obvious source
Water appearing under the sink without a clear connection leak may indicate a drain leak, a supply line pinhole, or water traveling along a surface before dripping. Dry everything, run the faucet, and watch carefully to isolate the source before proceeding.
Faucet Types and Why They Matter
Faucet repair is not one-size-fits-all. The internal mechanism determines which parts wear out, how the faucet disassembles, and what replacement parts you need. Buying the wrong cartridge or washer because you did not identify the faucet type first is the most common reason a faucet repair fails.
Most residential faucets fall into one of four categories. Look at the faucet handle configuration and, if possible, the brand and model number (often stamped on the faucet body or printed on the original packaging) before purchasing any parts.
Compression faucets
Two separate handles — one for hot, one for cold. Each handle compresses a rubber washer against a seat to stop water flow. When the washer wears out, the faucet drips. Common in older homes. Repair involves replacing the washer and sometimes the seat.
Cartridge faucets
Single-handle or two-handle designs that use a replaceable cartridge to control water flow and temperature. The cartridge is a self-contained unit that slides out and is replaced as a whole. Very common in modern residential faucets. Moen, Kohler, and many other brands use cartridge designs.
Ball faucets
Single-handle designs that use a rotating ball to control flow and temperature. The ball sits in a socket with springs, seats, and O-rings. When any of these components wear, the faucet drips. Delta and Peerless commonly use ball designs. Repair kits are available for most models.
Ceramic-disc faucets
Single-handle designs that use two ceramic discs — one fixed, one rotating — to control water. Ceramic discs are extremely durable and rarely fail. When they do, the repair usually involves cleaning the disc surfaces or replacing the ceramic cartridge. American Standard and some European brands use ceramic-disc designs.
When to DIY and When to Call a Plumber
Most faucet leaks are reasonable homeowner repairs. The tools are basic, replacement parts are widely available, and the process is well-documented for common faucet brands. That said, some situations call for a licensed plumber.
If the shutoff valve under the sink will not close fully — water continues to flow even with the valve turned all the way — do not proceed with the faucet repair. A shutoff valve that fails to close is a plumbing emergency in progress. Turn off the main house shutoff and call a licensed plumber. Do not force a corroded or stuck shutoff valve.
Safe to DIY
A dripping spout or handle leak on a standard residential faucet with functioning shutoff valves, accessible supply connections, and no signs of corrosion or water damage beyond the faucet itself.
Call a plumber
Shutoff valves that will not close fully, severely corroded supply lines or fittings, damaged or inaccessible plumbing inside the wall, active leaks that cannot be isolated, damaged sink or faucet mounting, plumbing configurations outside a standard residential setup, or any situation where you cannot safely stop the water supply before disassembly.
Tools and Materials
Most faucet repairs require only basic hand tools. The specific replacement parts depend on the faucet brand, model, and type — do not buy parts until you have identified the faucet and, ideally, removed the old component to match it.
Do not buy replacement parts before identifying your faucet type and, ideally, the brand and model number. A cartridge for a Moen 1225 will not fit a Moen 1200 or any other brand. Bring the old cartridge or O-ring to the hardware store for matching, or photograph the faucet brand and model number before you go.
Tools
- Adjustable wrench
- Basin wrench (for tight supply line connections under the sink)
- Phillips and flathead screwdrivers
- Hex key set (Allen wrenches) — for set screws on handles
- Needle-nose pliers
- Flashlight or headlamp
- Utility knife or pick tool (for removing O-rings)
- Towels and a small bucket
- Safety glasses
- Smartphone camera (to photograph component orientation before removal)
Materials
- Replacement cartridge (brand- and model-specific — match to your faucet)
- O-ring assortment or specific O-rings for your faucet model
- Replacement rubber washer and seat washer screw (for compression faucets)
- Ball faucet repair kit (for ball-type faucets — includes springs, seats, O-rings)
- Plumber's grease (silicone-based — for lubricating O-rings and seals)
- Plumber's tape (PTFE tape — for supply line threads if reconnecting)
- Replacement supply line (if the existing line shows age, kinking, or corrosion)
Shut Off the Water
Shutting off the water supply before disassembling any faucet component is non-negotiable. Even a slow drip becomes a significant flow when the faucet is open and the cartridge is removed.
Most bathroom and kitchen faucets have individual shutoff valves on the hot and cold supply lines under the sink. They are typically oval-handled or lever-handled valves on the supply lines coming out of the wall or floor. Turn each valve clockwise until it stops.
Never force a shutoff valve that feels stiff or corroded. A shutoff valve that has not been operated in years may be seized. Forcing it can break the valve stem, cause a leak at the packing nut, or rupture the supply line. If a valve feels stuck, apply gentle pressure only. If it will not move, turn off the main house shutoff and call a plumber.
- Open the cabinet under the sink and locate the hot and cold supply lines. Each should have its own shutoff valve.
- Turn the hot shutoff valve clockwise until it stops. Turn the cold shutoff valve clockwise until it stops.
- Turn on the faucet to verify water flow has stopped. Let any residual water drain from the lines.
- If water continues to flow after the valve is fully closed, the shutoff valve has failed. Do not proceed. Turn off the main house shutoff and call a licensed plumber.
- Leave the faucet handle in the open position while you work to relieve any remaining pressure in the lines.
Plug the Drain and Protect the Work Area
Small faucet components — set screws, retaining clips, cartridge retaining nuts — disappear down drains instantly. Plugging the drain before you start is a simple step that prevents a frustrating parts search.
Kitchen and bathroom sinks are often located near electrical outlets, garbage disposals, and under-sink appliances. Water and electricity are a dangerous combination. Keep the work area dry, do not use power tools near standing water, and if you are working near an outlet, turn off the circuit breaker for that outlet before you start.
- Insert the drain stopper or place a rag firmly in the drain opening.
- Place a folded towel in the sink basin to catch small parts and protect the sink surface.
- Place a small bucket or towels under the supply connections beneath the sink to catch residual water.
- If the faucet is near an electrical outlet or appliance, keep the work area dry and consider turning off the circuit breaker for that outlet as a precaution.
- Set out a clean towel or tray to organize removed components in the order they came off. Reassembly goes much faster when parts are laid out in sequence.
Remove the Handle
Handle attachment varies by faucet brand and model. Most handles are secured by a set screw hidden under a decorative cap, a visible screw on the top or back of the handle, or a retaining nut under the handle skirt. There is no universal removal method — look carefully before applying force.
Do not use excessive force to remove a stuck handle. Forcing a handle can crack the faucet body, damage the stem, or strip the set screw. If the handle will not come off after gentle wiggling and penetrating oil, consult the faucet manufacturer's service documentation or call a plumber.
- Look for a decorative cap on the top of the handle — a small plastic or metal disc that pops off with a flathead screwdriver or fingernail. The screw is usually underneath.
- If there is no cap, look for a set screw on the side or back of the handle. Set screws typically require a hex key (Allen wrench).
- Remove the screw or loosen the set screw. Do not discard it — set it on your organized parts tray.
- Pull the handle straight up and off the stem. If it resists, wiggle gently while pulling. Do not pry against the sink or faucet body.
- If the handle is stuck due to mineral buildup, apply a small amount of penetrating oil around the base and wait 10 minutes before trying again.
Identify the Internal Faucet Component
With the handle removed, you can see the internal mechanism. What you find determines the repair.
Photograph the assembly before removing anything. Orientation matters — a cartridge installed backward will not seal correctly, and a ball assembly reinstalled incorrectly will leak immediately.
Cartridge
A cylindrical plastic or brass unit that slides into the valve body. Usually held in place by a retaining clip or nut. Cartridges are brand- and model-specific. Note the orientation before removal — most cartridges have a front and back that must align correctly.
Ball assembly
A round ball sitting in a socket, surrounded by springs, rubber seats, and O-rings. Visible as a ball-shaped component when the handle is removed. Repair kits are available for most ball faucet brands and include all the wear components.
Compression stem
A threaded stem with a rubber washer at the bottom. Turning the handle screws the stem down, pressing the washer against a seat to stop water flow. The washer is at the bottom of the stem and is held by a brass screw.
Ceramic-disc cartridge
A wide, flat cartridge containing two ceramic discs. Usually secured by screws. Ceramic discs are durable — if a ceramic-disc faucet leaks, the discs may need cleaning rather than replacement. Inspect for mineral deposits before ordering a new cartridge.
Replace O-Rings and Seals
O-rings and rubber seals are the most common cause of handle leaks and base leaks. They are inexpensive, widely available, and straightforward to replace. The key is matching the replacement to the exact size of the original — O-rings come in dozens of sizes and the wrong size will not seal.
O-rings are found on cartridge stems, faucet body ports, and the faucet base. When a faucet leaks around the handle or at the base rather than from the spout, O-rings are the first thing to check.
Use only silicone-based plumber's grease on rubber O-rings and seals. Petroleum-based lubricants (WD-40, petroleum jelly) degrade rubber over time and will cause the new seal to fail prematurely. Silicone grease is available at any hardware store and is safe for all rubber plumbing components.
- Identify the O-ring location. On a cartridge faucet, O-rings are typically on the cartridge stem or on the valve body ports. On a faucet body, O-rings seal the base to the sink deck.
- Use a pick tool or the tip of a utility knife to carefully roll the old O-ring out of its groove. Do not cut into the groove or the faucet body.
- Take the old O-ring to the hardware store to match the size, or measure the inner diameter and cross-section diameter. Bring the faucet brand and model number if possible.
- Clean the O-ring groove with a damp cloth. Remove any mineral deposits or debris.
- Apply a thin coat of silicone-based plumber's grease to the new O-ring before installation. Do not use petroleum-based grease — it degrades rubber.
- Roll the new O-ring into the groove. Confirm it is fully seated and not twisted.
Replace a Cartridge
Cartridge replacement is the most common faucet repair for modern single-handle and two-handle faucets. The cartridge is a self-contained unit — when it fails, you replace the whole thing rather than trying to rebuild individual seals inside it.
The critical rule: match the replacement cartridge to the exact faucet brand and model. Bring the old cartridge to the hardware store or order by model number. A cartridge that is close but not exact will not seal correctly.
Installing a cartridge in the wrong orientation is one of the most common reassembly errors. A backward cartridge will reverse hot and cold, fail to stop water flow, or leak immediately. Always photograph the original orientation before removal and confirm alignment before reinstalling the retaining hardware.
- Photograph the cartridge orientation before removal. Note which direction the cartridge faces — most have a front marking or a tab that aligns with a notch in the valve body.
- Remove the retaining clip or retaining nut that holds the cartridge in place. Retaining clips are usually U-shaped metal clips that pull straight out with pliers. Retaining nuts unscrew counterclockwise.
- Pull the cartridge straight up and out of the valve body. Some cartridges require a cartridge puller tool — available at hardware stores for common brands. Do not twist the cartridge during removal unless the manufacturer's instructions specify rotation.
- Inspect the valve body interior. Clean out any mineral deposits or debris with a damp cloth.
- Apply a thin coat of silicone grease to the O-rings on the new cartridge.
- Insert the new cartridge in the correct orientation. Align any tabs or notches. Press firmly until fully seated.
- Reinstall the retaining clip or retaining nut. The clip should snap fully into its groove. The nut should be snug but not overtightened.
Repair Compression-Style Faucets
Compression faucets are the oldest residential faucet design and are still common in older homes. Each handle has its own stem with a rubber washer at the bottom. When you turn the handle off, the stem screws down and presses the washer against a brass seat to stop water flow. When the washer wears out, the faucet drips.
The repair is straightforward: remove the stem, replace the washer, and reassemble. If the faucet still drips after a new washer, the brass seat may be damaged and need to be resurfaced or replaced — a seat wrench is required for that step.
- With the handle removed, use an adjustable wrench to unscrew the packing nut counterclockwise. The stem will come out with the nut.
- Examine the rubber washer at the bottom of the stem. A worn washer will be flattened, cracked, or grooved.
- Remove the brass screw holding the washer. Replace the washer with an exact match — bring the old one to the hardware store.
- Inspect the brass seat inside the valve body with a flashlight. A smooth, flat seat is correct. A rough, pitted, or grooved seat will damage new washers quickly and requires resurfacing with a seat wrench or seat replacement.
- Reinstall the stem with the new washer. Tighten the packing nut snugly — do not overtighten.
Ball and Ceramic-Disc Faucets
Ball faucets and ceramic-disc faucets use different internal components than cartridge and compression designs. The repair approach differs accordingly.
For ball faucets, the most practical repair is a brand-specific repair kit that includes all the wear components — springs, rubber seats, O-rings, and sometimes a new ball. Attempting to replace only one component in a worn ball assembly often results in a second repair shortly after. Replace the full kit.
For ceramic-disc faucets, the discs themselves rarely fail. If a ceramic-disc faucet leaks, start by removing the cartridge and cleaning the ceramic surfaces with white vinegar to remove mineral deposits. If cleaning does not resolve the leak, the ceramic cartridge can be replaced — but confirm the replacement is the correct model for your faucet.
Ball faucet repair kits are brand- and model-specific. A Delta repair kit will not work in a Peerless or Moen ball faucet, even though the designs look similar. Confirm the brand and model before purchasing a kit. The faucet brand is usually stamped on the faucet body or visible on the original packaging.
Reassemble the Faucet
Reassembly is the reverse of disassembly, but with two critical rules: correct orientation and no overtightening. A component installed backward will leak. A fitting overtightened will crack the faucet body or damage the cartridge.
Do not overtighten plastic retaining nuts, cartridge retaining hardware, or handle screws. Plastic faucet components crack under excessive torque. Snug is sufficient — if you need a wrench to tighten it further, you are already past the correct torque. Overtightening is one of the most common causes of a second repair trip.
- Reinstall the cartridge, ball assembly, or stem in the correct orientation. Refer to your photographs from disassembly.
- Reinstall the retaining clip, retaining nut, or packing nut. Tighten snugly — firm hand pressure is sufficient. Do not use a wrench to overtighten plastic retaining nuts.
- Reinstall any decorative collar or escutcheon that sits between the handle and the sink deck.
- Slide the handle back onto the stem. Confirm it moves freely through its full range of motion before securing it.
- Reinstall the handle screw or tighten the set screw. Replace the decorative cap if applicable.
- Check that the handle operates smoothly — no binding, no excessive resistance, no grinding.
Restore Water and Test
Restoring water after a faucet repair should be done slowly and deliberately. Opening the shutoff valves too quickly can cause a water hammer effect and may dislodge a newly seated cartridge or seal before it has a chance to seat under normal pressure.
- Remove the drain plug or rag from the drain.
- Slowly open the cold shutoff valve — a quarter turn at a time, pausing between turns. Watch the supply connection for any drips.
- Slowly open the hot shutoff valve the same way.
- With both shutoffs open, turn on the faucet and let water run for 30 seconds. Check for drips at the spout, around the handle, and at the faucet base.
- Test hot and cold operation separately. Confirm the handle moves correctly and water temperature responds as expected.
- Look under the sink. Check the supply line connections and the shutoff valves for any moisture.
- Turn the faucet off completely and wait two minutes. Check the spout for any residual dripping.
If the Faucet Still Drips
A faucet that still drips after a cartridge or washer replacement is not unusual. The most common causes are an incorrect replacement part, incorrect reassembly, or a secondary problem that was not visible until the primary repair was made.
Faucet drips from the spout after cartridge replacement
Confirm the replacement cartridge is the correct model for your faucet brand and model number. A close-but-not-exact cartridge will not seal. Also confirm the cartridge is installed in the correct orientation — a backward cartridge will not stop water flow.
Faucet leaks around the handle after reassembly
The O-ring on the cartridge stem or valve body port is not sealing. Disassemble and inspect the O-rings. Confirm they are the correct size, fully seated in their grooves, and lubricated with silicone grease.
Compression faucet still drips after new washer
The brass seat is damaged. A worn or pitted seat will destroy new washers quickly. The seat needs to be resurfaced with a seat wrench or replaced. If you do not have a seat wrench, this is a reasonable point to call a plumber.
Faucet leaks at the base after reassembly
The O-rings on the faucet body are not sealing. These are separate from the cartridge O-rings and require removing the faucet from the sink deck to access. If the faucet is old, this may be a good time to consider replacement rather than continued repair.
Water flow is reduced after repair
Debris from the repair may have entered the aerator. Unscrew the aerator from the spout tip and rinse it under water. Also check that the shutoff valves are fully open.
Hot and cold are reversed after repair
The cartridge was installed backward. Disassemble, rotate the cartridge 180 degrees, and reassemble.
Handle is stiff or hard to turn after reassembly
The retaining nut or packing nut is overtightened, or the cartridge is not fully seated. Loosen the retaining hardware slightly and test the handle movement.
Leak at supply line connection after repair
The supply line connection was disturbed during the repair. Tighten the connection a quarter turn with a wrench. If the leak continues, the supply line or shutoff valve packing may need replacement.
Common Mistakes
- Failing to shut off both the hot and cold supply valves before disassembly — even a slow trickle becomes a significant flow when the cartridge is removed.
- Not plugging the drain — set screws and retaining clips disappear down drains in an instant.
- Buying replacement parts before identifying the faucet brand, model, and type — a cartridge that is close but not exact will not seal.
- Forcing a corroded or stuck shutoff valve — a valve that will not close needs a plumber, not more force.
- Installing the cartridge in the wrong orientation — a backward cartridge reverses hot and cold or fails to stop water flow.
- Using petroleum-based lubricant on O-rings — petroleum products degrade rubber; use silicone-based plumber's grease only.
- Overtightening retaining nuts and handle screws — plastic faucet components crack under excessive torque.
- Failing to clean the valve body interior before installing the new cartridge — debris left in the valve body will damage the new cartridge.
- Not photographing component orientation before removal — reassembly errors are almost entirely caused by forgetting which way things came out.
- Failing to check under the sink after restoring water — supply line connections and shutoff valve packing can drip slowly without being immediately obvious.
Final Checklist and Faucet Maintenance
Before calling the repair complete, run through this checklist. A repair that passes all of these checks is done. A repair that fails any of them needs another look before you put the cabinet doors back on.
- Both hot and cold shutoff valves fully reopened
- Faucet operates correctly — handle moves smoothly through full range
- No dripping from the spout with faucet fully off — observed for at least two minutes
- No leak visible at the faucet base or around the handle
- No moisture at supply line connections under the sink
- No moisture at shutoff valves
- Hot and cold operate correctly — temperature responds as expected
- Aerator flow is normal — no reduced flow from debris
- Drain plug removed
- Work area cleaned and dried
- Old parts disposed of appropriately
- Repair confirmed dry after 24 hours — check under the sink again the next day
Basic faucet maintenance extends the life of the repair: clean the aerator every six to twelve months to prevent mineral buildup, avoid using the faucet handle as a support when leaning over the sink, and address any new drips promptly. A faucet that starts dripping again within a few months of repair usually means the replacement cartridge was not the correct model, or a secondary component was not addressed.
CCCT Takeaway
- Identify the leak location before disassembly — spout drip, handle leak, base leak, and supply connection leak each point to a different component.
- Know your faucet type. Compression, cartridge, ball, and ceramic-disc faucets use different parts and different repair procedures.
- Match replacement parts to the exact faucet brand and model. A close-but-not-exact cartridge will not seal.
- Photograph component orientation before removal. A cartridge installed backward reverses hot and cold or fails to stop water flow.
- If the shutoff valve will not close, stop. That is a plumber call, not a faucet repair.
Need a Pro?
JTC Renovations
When the shutoff valve won't close, the supply lines are corroded, or the faucet repair has revealed a bigger plumbing problem, JTC Renovations can handle it. Licensed, experienced, and no guesswork.
Visit JTC RenovationsFrequently Asked Questions
- How do I know what type of faucet I have?
- Look at the handle configuration first: two separate handles usually indicate a compression or two-handle cartridge faucet; a single handle that moves side to side and up and down is typically a ball or single-handle cartridge faucet; a single handle that moves only side to side is often a ceramic-disc design. The faucet brand is usually stamped on the body or visible on the original packaging. Knowing the brand and model number is the most reliable way to identify the correct replacement parts.
- Can I fix a leaky faucet without turning off the water?
- No. Any faucet disassembly — removing a handle, extracting a cartridge, replacing a washer — requires the water supply to be shut off first. Even a slow drip becomes a significant flow when the faucet is open and the cartridge is removed. Locate the shutoff valves under the sink and close both the hot and cold supplies before starting any repair.
- How long does a faucet cartridge last?
- A quality cartridge in a residential faucet typically lasts 10 to 20 years under normal use. Hard water accelerates wear by depositing minerals on the cartridge seals. If a faucet starts dripping within a year or two of a cartridge replacement, the replacement cartridge may not have been the correct model, or the valve seat or O-rings were not addressed during the repair.
- Is it worth repairing an old faucet or should I replace it?
- If the faucet is more than 15 to 20 years old, leaks at the base (indicating worn body O-rings), or requires parts that are difficult to source, replacement is often more practical than repair. A new mid-range faucet costs $80 to $200 and comes with a warranty. If the faucet is a quality brand with readily available cartridges and the leak is a straightforward cartridge or O-ring issue, repair is the better value.
- What if the shutoff valve under my sink will not close?
- Do not force it. A shutoff valve that will not close fully is a plumbing problem that needs to be addressed before the faucet repair can proceed. Turn off the main house water shutoff — usually located where the main water line enters the house or near the water meter — and call a licensed plumber to replace the shutoff valve. Forcing a corroded or seized valve can break the stem and cause an immediate leak.
More plumbing guides are on the way.
Plumbing Hub