How to Replace a Toilet

Replacing a toilet is one of the more satisfying plumbing projects a homeowner can tackle. It looks intimidating, but the process is straightforward: shut off the water, disconnect the supply, remove the old toilet, clean the flange, set the new seal, lower the new toilet, and reconnect. Most homeowners can complete the job in two to four hours with basic tools.

Homeowner installing a new toilet in a residential bathroom during a DIY plumbing replacement

Toilets last a long time, but they do eventually need to be replaced — whether because of a cracked bowl or tank, persistent leaks, inefficient water use, or simply an upgrade. The job involves disconnecting a water supply line, removing a heavy porcelain fixture, cleaning a floor flange, and installing a new toilet with a fresh seal. None of those steps require specialized plumbing knowledge.

The most important part of the job happens before you buy anything: measuring the rough-in distance and inspecting the existing flange. A toilet that does not fit the rough-in or a flange that needs repair will stop the project before it starts. This guide walks through every step, including what to do when something unexpected turns up.

DIY or Call a Pro?

A standard toilet replacement — same rough-in, intact flange, functioning shutoff valve — is a reasonable DIY project for most homeowners. The tools are basic, the parts are widely available, and the process is well-documented.

That said, some situations call for a licensed plumber. If you encounter any of the conditions below, stop the project and call a professional before proceeding.

Safe to DIY

Standard toilet replacement with the same rough-in, intact flange, functioning shutoff valve, and no signs of subfloor damage or active leaks beyond the toilet itself.

Call a Plumber

Broken or severely damaged flange, significant subfloor rot or water damage, failed shutoff valve that will not close, damaged drain piping, sewer-line problems, or any plumbing configuration outside a basic toilet swap.

What You Are Actually Replacing

Understanding the components helps you buy the right parts and recognize problems during removal.

Toilet Bowl and Tank

The bowl sits on the floor and connects to the drain. The tank holds water for flushing. Most residential toilets are two-piece (separate bowl and tank) or one-piece (combined). Both are replaced as a unit in a standard swap.

Wax or Alternative Sealing Ring

A compressible ring — traditionally wax, now also available in wax-free foam or rubber — seals the toilet horn to the closet flange. It prevents sewer gas and wastewater from escaping at the base. It is replaced every time the toilet is removed.

Closet Flange

The floor-mounted fitting that connects the toilet drain to the drain pipe. Mounting bolts (closet bolts or johnny bolts) slide into the flange and secure the toilet to the floor. A damaged or improperly positioned flange must be repaired before the new toilet is installed.

Supply Line and Shutoff Valve

The braided or ribbed supply line connects the shutoff valve (usually on the wall behind the toilet) to the fill valve inside the tank. Both are inspected during removal and replaced if they show signs of age, corrosion, or damage.

Toilet Seat

Sold separately from most toilets. Measure the bowl shape (round or elongated) and confirm the seat mounting hole spacing before purchasing.

Before You Buy a Replacement Toilet

Buying the wrong toilet is the most common and most avoidable mistake in this project. Measure before you shop.

  1. Measure the rough-in: the distance from the finished wall (not the baseboard or trim) to the centerline of the closet bolts or the center of the drain opening. Standard rough-in is 12 inches. Some older homes have 10-inch or 14-inch rough-ins. Do not measure from the baseboard — measure from the wall surface itself.
  2. Check bowl shape: round bowls are shorter front-to-back and fit smaller bathrooms. Elongated bowls are longer and more common in newer construction. Measure the available floor space before choosing.
  3. Check toilet height: standard height is approximately 14 to 15 inches to the rim. Comfort height (ADA-compliant) is approximately 16 to 18 inches. Comfort height is easier for most adults to use.
  4. Check tank clearance: measure the distance from the wall to the back of the existing toilet. Confirm the new tank will fit without touching the wall or obstruction.
  5. Check the supply connection location: most toilets connect at the bottom-left of the tank. Confirm the supply line will reach the fill valve on the new toilet.
  6. Inspect the flange condition before purchasing: if the flange is broken, corroded, or set below the finished floor, you may need a repair kit or a plumber before the new toilet can be installed correctly.

Tools and Materials

Gather everything before you start. Once the water is off and the old toilet is out, you want to move efficiently.

Tools & Materials

  • Adjustable wrench or channel-lock pliers
  • Utility knife or putty knife
  • Hacksaw or mini hacksaw (for trimming mounting bolts if needed)
  • Level (torpedo or 4-foot)
  • Tape measure
  • Bucket (2 to 3 gallon)
  • Sponge and old towels
  • Rubber gloves and eye protection
  • Wax ring or wax-free seal (sized for your flange and toilet horn)
  • New closet bolts (usually included with wax ring kits)
  • New braided supply line (12 to 16 inch, sized to fit your shutoff valve)
  • Plastic shims (toilet-specific, if needed for leveling)
  • Silicone caulk (for base sealing if desired)

Shut Off the Water

The shutoff valve is typically located on the wall behind and below the toilet tank. It controls water flow to the toilet only — not the rest of the house.

Do not force a shutoff valve that is stuck, corroded, or leaking around the stem. Forcing a deteriorated valve can cause it to fail completely. Shut off the main water supply and call a plumber.

  1. Turn the shutoff valve clockwise until it stops. Most valves are oval-handled or have a flat slot for a screwdriver. Do not force a valve that feels stuck or corroded — a deteriorated valve can fail and cause a larger leak.
  2. Flush the toilet and confirm the tank does not refill. If the tank continues to fill after the valve is closed, the valve is not seating properly.
  3. If the shutoff valve will not close or is leaking around the stem, shut off the main water supply to the house and call a plumber to replace the valve before continuing.

Drain and Empty the Existing Toilet

Removing as much water as possible before disconnecting and lifting the toilet makes the job cleaner and lighter.

Toilet water — even from the tank — can contain bacteria and contaminants. Wear rubber gloves throughout this process. Dispose of sponge water in a utility sink or toilet in another bathroom, not in a kitchen sink.

  1. Flush the toilet. Hold the handle down to allow as much water as possible to drain from the tank and bowl.
  2. Remove remaining tank water: use a sponge to soak up water from the tank and wring it into a bucket. The tank should be essentially empty before you disconnect the supply line.
  3. Remove remaining bowl water: use a sponge or a small cup to remove as much water as possible from the bowl. Some water will remain in the trap — have towels ready.

Disconnect the Water Supply

With the water off and the tank emptied, disconnect the supply line.

  1. Place a towel or small bucket under the supply line connection at the bottom of the tank. There will be residual water.
  2. Using an adjustable wrench or channel-lock pliers, turn the supply line nut counterclockwise at the tank connection. Hand-loosen first, then use the wrench only if needed.
  3. Disconnect the other end of the supply line from the shutoff valve. Inspect the supply line for corrosion, kinking, or damage. Replace it — supply lines are inexpensive and a failed supply line can cause significant water damage.

Remove the Existing Toilet

A standard two-piece toilet weighs 60 to 100 pounds. A one-piece toilet can weigh 100 pounds or more. Have a helper if possible, especially for one-piece units.

Toilets are heavy and awkward. Lift with your legs, not your back. Get a helper for one-piece toilets. Porcelain can crack or shatter if dropped — broken porcelain creates sharp edges. Wear gloves and eye protection.

  1. Pry off the plastic caps at the base of the toilet (usually two, one on each side). These cover the mounting nuts on the closet bolts.
  2. Remove the mounting nuts using an adjustable wrench. Turn counterclockwise. If the bolt spins with the nut, grip the bolt with pliers while turning the nut.
  3. If the toilet is caulked to the floor, score the caulk line with a utility knife before attempting to lift. Do not pry aggressively against the flange.
  4. Gently rock the toilet side to side to break the wax seal. Lift straight up — do not twist or pry against the floor or flange. Keep the toilet as upright as possible to contain residual water in the trap.
  5. Move the toilet to a protected surface — cardboard or old towels on the floor. Porcelain chips and cracks easily when set on hard surfaces.

Remove the Old Seal and Inspect the Flange

This is the most important inspection step in the entire project. A damaged flange that is not repaired before the new toilet is installed will result in leaks, odors, and a rocking toilet — sometimes immediately, sometimes months later.

Do not skip the flange inspection. A broken, loose, or improperly positioned flange will cause the new toilet to leak or rock. If the flange is damaged, repair it before installing the new toilet. Significant subfloor damage requires a contractor — do not install a toilet over a compromised subfloor.

  1. Stuff a rag into the drain opening to block sewer gas while you work. Sewer gas contains hydrogen sulfide and methane — both are hazardous in enclosed spaces.
  2. Scrape the old wax or sealing material completely off the flange using a putty knife. The flange surface must be clean and smooth before the new seal is installed. Old wax left on the flange will prevent the new seal from seating correctly.
  3. Inspect the flange ring for cracks, breaks, or missing sections. A cracked flange cannot hold the toilet securely and will allow the seal to fail.
  4. Check whether the flange is loose. Press down on the flange ring — it should not move. A loose flange must be re-secured to the subfloor before the toilet is installed.
  5. Check the flange height relative to the finished floor. The top of the flange should be at or slightly above the finished floor surface. A flange set too low may require a flange extender ring.
  6. Look for signs of water damage around the flange: soft or discolored flooring, soft subfloor, or staining. If the subfloor is soft or damaged, stop and call a plumber or contractor before proceeding.

Prepare the Floor and Flange

The floor and flange must be clean, dry, and level before the new seal and toilet are installed.

  1. Clean the flange surface and the surrounding floor area. Remove all old wax, debris, and residue.
  2. Dry the area completely. The seal will not compress and seat correctly on a wet surface.
  3. Install new closet bolts into the flange slots. Position them so they are centered in the slot and aligned with each other. The bolts should be parallel and equidistant from the wall.
  4. Check the floor for level at the flange location. Use a torpedo level across the flange opening in two directions. Note any high or low spots — you may need shims when the toilet is set.

Install the New Seal and Toilet

The seal is installed once. Once the toilet is set and compressed onto the seal, the toilet should not be lifted again — lifting breaks the seal and requires a new one.

Once the toilet is set on the seal, do not lift it. Lifting breaks the seal and requires a new wax ring. If you need to reposition the toilet, remove it completely, install a new seal, and start again.

  1. Position the seal according to the manufacturer's instructions. Wax rings are typically pressed onto the toilet horn (the outlet at the bottom of the bowl) with the wax side facing down toward the flange. Some wax-free seals mount to the flange instead — follow the product instructions.
  2. Remove the rag from the drain opening.
  3. Lift the toilet and position it directly over the flange, aligning the mounting holes in the toilet base with the closet bolts. This is easier with a helper — one person guides the bolts through the holes while the other controls the toilet.
  4. Lower the toilet straight down onto the flange. Do not twist or rock the toilet as it contacts the seal — this can displace the wax and create gaps in the seal.
  5. Apply firm, even downward pressure by pressing down on the rim of the bowl. The toilet should settle to the floor as the seal compresses. Do not sit on the toilet to compress the seal until the mounting hardware is installed.

Secure and Level the Toilet

The toilet must be level and stable before the water is reconnected. A toilet that rocks will eventually break the seal and leak.

Do not overtighten the mounting nuts. Porcelain is brittle — overtightening can crack the base of the toilet. Tighten until snug and stable, then stop.

  1. Install the washers and nuts onto the closet bolts by hand. Do not use a wrench yet.
  2. Check the toilet for level in both directions using a torpedo level on the rim or tank. If the toilet rocks or is not level, slide plastic toilet shims under the base at the low points.
  3. Tighten the mounting nuts gradually, alternating sides — a quarter turn on one side, then a quarter turn on the other. Check level after each round of tightening.
  4. Stop tightening when the toilet is snug and does not rock. Do not overtighten — porcelain cracks under excessive torque. The toilet should feel solid, not flex, but the nuts should not be forced.
  5. If the closet bolts extend more than about half an inch above the nuts, trim them with a hacksaw or mini hacksaw. The bolt caps will not seat correctly over excessively long bolts.
  6. Press the plastic bolt caps into place over the nuts. Snap or press them down until they seat against the base.

Reconnect the Water Supply

Use a new braided supply line. Old supply lines can fail without warning — a failed supply line under pressure can cause significant water damage.

  1. Connect the supply line to the fill valve at the bottom of the tank. Hand-tighten the nut first, then snug it with a wrench — one quarter to one half turn past hand-tight. Do not overtighten.
  2. Connect the other end of the supply line to the shutoff valve. Hand-tighten, then snug with a wrench. Confirm the line is not kinked or bent sharply.
  3. Slowly open the shutoff valve counterclockwise. Open it gradually — do not open it fully in one motion. Watch the supply line connection at the tank for drips as the tank fills.

Test for Leaks

Do not assume the installation is complete until you have performed a systematic leak check. A slow leak at the base may not be visible until after several flushes.

A leak at the base of the toilet after flushing means the seal has failed. Do not continue using the toilet. Remove it, install a new seal, and reinstall. Water leaking under the base can damage the subfloor and create mold over time.

  1. Allow the tank to fill completely. While it fills, inspect the supply line connections at both ends — the shutoff valve and the tank — for any drips or moisture.
  2. Inspect the tank-to-bowl connection (on two-piece toilets) for any drips while the tank fills.
  3. Flush the toilet and watch the base carefully during and immediately after the flush. Any water appearing at the base during a flush indicates a failed seal.
  4. Flush three to five times. Dry the floor completely between flushes so you can detect any new moisture. A wax seal failure may not appear on the first flush.
  5. After the final flush, dry the entire base area and place a dry paper towel around the base. Check the paper towel after 10 to 15 minutes. Any moisture indicates a leak.

Install the Seat and Final Components

With the toilet confirmed leak-free, complete the installation.

  1. Install the toilet seat: align the seat hinges with the mounting holes at the back of the bowl. Insert the bolts and tighten the nuts from underneath. The seat should be centered and should not slide side to side.
  2. Place the tank lid on the tank. Confirm it sits flat and does not rock.
  3. Check the flush handle or button. The chain connecting the handle to the flapper should have about half an inch of slack — enough to allow the flapper to close fully, but not so much that it gets caught under the flapper.
  4. Check the fill level: the water in the tank should fill to the marked water line inside the tank, typically about an inch below the top of the overflow tube. Adjust the fill valve float if needed, following the manufacturer's instructions.
  5. If desired, apply a thin bead of silicone caulk around the base of the toilet where it meets the floor, leaving the back open. This prevents water from getting under the base during cleaning — but note that caulking the entire base can hide a seal leak. Some plumbers prefer to leave the base uncaulked for this reason.

Common Problems and When to Stop

Most problems that appear after a toilet replacement have a specific cause and a specific fix. Here is what to look for and when to call a professional.

Toilet rocks after installation

The floor is not level or the seal did not compress evenly. Remove the toilet, install a new seal, and use plastic shims to level the toilet before tightening the mounting nuts.

Water at the base after flushing

The seal has failed. Remove the toilet, install a new wax ring, and reinstall. Do not continue using a toilet with a base leak.

Drip at the supply line connection

Hand-tighten the connection, then snug it slightly with a wrench. If it continues to drip, replace the supply line — the ferrule or threads may be damaged.

Toilet not filling or filling slowly

Check that the shutoff valve is fully open. If the valve is open and the fill rate is still slow, the fill valve may be partially blocked or defective — replace it.

Toilet continuously running after installation

The flapper is not seating correctly, the chain has too much slack and is caught under the flapper, or the fill valve is not shutting off. Adjust the chain, check the flapper seal, or replace the fill valve.

Weak or incomplete flush

Check the water level in the tank — it should be at the marked fill line. If the level is correct, the flush valve or flapper may not be opening fully. Adjust the chain or replace the flapper.

Sewer odor after installation

The seal may not have compressed fully, or the rag was left in the drain. Confirm the rag was removed. If the odor persists, the seal has likely failed — remove and reinstall.

Damaged or broken flange discovered during removal

Stop. A broken flange cannot hold the toilet securely. Repair options include a flange repair ring for minor damage. Significant damage requires a plumber.

Soft or damaged subfloor discovered during removal

Stop. Do not install a new toilet over a compromised subfloor. Call a contractor to assess and repair the subfloor before the toilet is reinstalled.

Shutoff valve will not close or is leaking

Shut off the main water supply to the house. Call a plumber to replace the shutoff valve before continuing.

Final Checklist and Maintenance

Before you consider the job complete, run through this checklist. Then review the basic maintenance steps that will help the new toilet last.

  • Water supply restored and shutoff valve fully open
  • No visible drips at supply line connections (shutoff valve and tank)
  • No visible drips at tank-to-bowl connection (two-piece toilets)
  • Toilet does not rock — base is stable and level
  • Flush operates correctly — bowl clears completely
  • Tank fills to the correct level and shuts off
  • No water at the base after three to five flushes
  • Floor area around base is dry after 15 minutes
  • Mounting hardware is secure — bolt caps in place
  • Toilet seat is centered and secure
  • Tank lid is seated correctly
  • Work area cleaned and tools removed

Basic maintenance: inspect the supply line and shutoff valve annually for corrosion or moisture. Check the base for any signs of water after heavy use. Replace the flapper every three to five years or when the toilet begins to run intermittently. A toilet that rocks should be addressed immediately — do not wait for a visible leak.

CCCT Takeaway

  • Measure the rough-in before you buy anything — a toilet that does not fit the rough-in cannot be installed without moving the drain.
  • Inspect the flange before the new toilet goes in. A damaged flange will cause the new toilet to leak or rock regardless of how carefully it is installed.
  • Once the toilet is set on the seal, do not lift it. Lifting breaks the seal and requires a new wax ring.
  • Tighten mounting nuts until snug — not until tight. Overtightening cracks porcelain.
  • Test with three to five flushes and dry the base completely between each one. A slow seal leak may not appear on the first flush.

Need a Pro?

JTC Renovations

When the flange is damaged, the subfloor needs attention, or the shutoff valve won't cooperate, JTC Renovations has the experience to handle what a basic DIY guide can't. Get the job done right the first time.

Visit JTC Renovations

Frequently Asked Questions

How do I measure the rough-in for a toilet?
Measure from the finished wall surface — not the baseboard or trim — to the center of the closet bolts or the center of the drain opening. Standard rough-in is 12 inches. Measure before purchasing a replacement toilet. If the existing toilet is still in place, measure from the wall to the center of the bolt caps at the base.
Do I need to replace the wax ring every time I remove a toilet?
Yes. A wax ring is a single-use seal. Once it has been compressed and then disturbed by removing the toilet, it cannot reliably re-seal. Always install a new wax ring — or wax-free alternative — whenever a toilet is removed and reinstalled.
What does it mean if the toilet rocks after installation?
A rocking toilet means the base is not making even contact with the floor. This is usually caused by an uneven floor, a flange that is not flush with the finished floor, or mounting nuts that were not tightened evenly. Use plastic toilet shims to stabilize the base, then tighten the mounting nuts gradually and alternately. A toilet that continues to rock after shimming may have a flange problem that requires professional repair.
Is it safe to caulk around the base of a toilet?
Caulking the base is a common practice that prevents water from getting under the toilet during cleaning. However, caulking the entire perimeter can hide a seal leak — water that would otherwise appear at the base gets trapped underneath. Some plumbers prefer to leave the back of the base uncaulked so that a seal failure is visible. If you caulk, inspect the base periodically for any signs of moisture.
When should I call a plumber instead of replacing the toilet myself?
Call a plumber if you find a broken or severely damaged flange, significant subfloor rot or water damage, a shutoff valve that will not close, damaged drain piping, or any plumbing configuration that goes beyond a straightforward toilet swap. A standard replacement with an intact flange and functioning shutoff valve is a reasonable DIY project. Anything beyond that scope is worth a professional assessment.

More plumbing guides are on the way.

Plumbing Hub